-
Zextras Carbonio 23.6.0
-
-
- Older Version's Changelogs
- Changelog Version 23.2.0
- Changelog version 23.3.0
- Changelog Version 23.4.0
- Changelog Version 23.5.0
- Changelog Version 23.7.0
- Changelog Version 23.6.0
- Changelog version 23.9.0
- Changelog Version 23.10.0
- Changelog for Release 23.11.0 of Carbonio
- Changelog for Release 23.12.0 of Carbonio
-
-
-
-
Carbonio Community Edition
-
Suite for Zimbra
- Zextras Suite documentation
- Introduction
- Installation Instructions for Zextras Suite
- Licencing of Zextras Suite
- File Management for Licences
- Zextras Backup
- Backup and Restore by Zextras
- Zextras Backup Advanced Methods
- Zextras for Mobile
- Service for Address Books
- Troubleshooting Zextras Mobile
- Powerstore Zextras
- The Indexing of Attachments
- Extractor of External Content
- Delegated Admin Provisioning Zextras Admin
- The Zextras Drive
- Docs Zextras
- Authentique Zextras
- Team Zextras
- Video Server Zextras
- CLI
- next6 back
-
- Changelog for Zextras 3.1.x releases
- Changelog for Zextras Suite 3.2.0
- Changelog for Zextras Suite 3.3.0
- Zextras Suite Changelog - Release 3.4.0
- Changelog for Zextras Suite 3.5.0
- Changelog for Zextras Suite 3.6.0
- Changelog for Zextras Suite 3.7.0
- Changelog for Zextras Suite 3.8.0
- Changelog for Zextras Suite 3.9.0
- Changelog for Zextras Suite 3.10.0
- Changelog for Zextras Suite 3.11.0
- Changelog for Zextras Suite 3.12.0
- Changelog for Zextras Suite 3.13.0
- Changelog for Zextras Suite 3.14.0
- Changelog for Zextras Suite 3.15.0
- Changelog for Zextras Suite 3.16.0
- Changelog for Zextras Suite 3.17.0
- Changelog for Zextras Suite 3.18.0
- Zextras Suite Changelog - Release 3.19.0
- next4 back
How to add an AppServer Node to an existing Carbonio CE installation is described in this section. This is helpful when you need to scale up your infrastructure due to an increase in the number of mailboxes.
Preliminaries
Please carefully go through the whole installation process on this page before attempting to install a new AppServer, and make sure the following conditions are met.
- Already, a Carbonio CE infrastructure is functioning properly.
- There is a new node that meets the multi-server requirements and has already completed the preliminary tasks. This node will be known as SRV11.example.com.
- The root user must be used to run all commands.
- The steps to take are simple and the same as for the SRV3: AppServer and Carbonio Storages CE Node.
Carbonio Bootstrap
the Carbonio bootstrap procedure to begin
You must supply these values during the procedure, which you may do by retrieving them from SRV1.
- The FQDN of SRV1, srv1.example.com, is LDA master host.
- The command is used to acquire the Ldap Admin password from SRV1.
Configure Carbonio Mesh
The agent for Carbonio Mesh will be installed; it will connect to and communicate with the server. By using the launching command, the agent’s configuration is built.
This instruction will:
- demand the current Node’s IP address and netmask.
- Request the Carbonio Mesh secret from the SRV1 server, which is located in the file /var/lib/service-discover/password.
Run the subsequent command when the setup has been finished successfully, this time using the secret.
Lastly, restart the service.
Finished installation
Restarting all services is the final step to take.
Use the following command to verify that the Node was added correctly:
The new node should be included in the output, like in:
Use command to verify that all services are operational.